From: Abhishek Sahu <absahu@codeaurora.org>
Date: Fri, 11 Aug 2017 17:09:16 +0530
Subject: [PATCH] mtd: nand: qcom: fix read failure without complete bootchain
References: bnc#1060662
Patch-mainline: 4.12.13
Git-commit: d8a9b320a26c1ea28e51e4f3ecfb593d5aac2910
commit d8a9b320a26c1ea28e51e4f3ecfb593d5aac2910 upstream.
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is
0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Fixes: c76b78d8ec05a ("mtd: nand: Qualcomm NAND controller driver")
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
---
drivers/mtd/nand/qcom_nandc.c | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/qcom_nandc.c
index 57d483ac5765..a45e61fe0a66 100644
--- a/drivers/mtd/nand/qcom_nandc.c
+++ b/drivers/mtd/nand/qcom_nandc.c
@@ -109,7 +109,11 @@
#define READ_ADDR 0
/* NAND_DEV_CMD_VLD bits */
-#define READ_START_VLD 0
+#define READ_START_VLD BIT(0)
+#define READ_STOP_VLD BIT(1)
+#define WRITE_START_VLD BIT(2)
+#define ERASE_START_VLD BIT(3)
+#define SEQ_READ_START_VLD BIT(4)
/* NAND_EBI2_ECC_BUF_CFG bits */
#define NUM_STEPS 0
@@ -148,6 +152,10 @@
#define FETCH_ID 0xb
#define RESET_DEVICE 0xd
+/* Default Value for NAND_DEV_CMD_VLD */
+#define NAND_DEV_CMD_VLD_VAL (READ_START_VLD | WRITE_START_VLD | \
+ ERASE_START_VLD | SEQ_READ_START_VLD)
+
/*
* the NAND controller performs reads/writes with ECC in 516 byte chunks.
* the driver calls the chunks 'step' or 'codeword' interchangeably
@@ -672,8 +680,7 @@ static int nandc_param(struct qcom_nand_host *host)
/* configure CMD1 and VLD for ONFI param probing */
nandc_set_reg(nandc, NAND_DEV_CMD_VLD,
- (nandc->vld & ~(1 << READ_START_VLD))
- | 0 << READ_START_VLD);
+ (nandc->vld & ~READ_START_VLD));
nandc_set_reg(nandc, NAND_DEV_CMD1,
(nandc->cmd1 & ~(0xFF << READ_ADDR))
| NAND_CMD_PARAM << READ_ADDR);
@@ -1972,13 +1979,14 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc)
{
/* kill onenand */
nandc_write(nandc, SFLASHC_BURST_CFG, 0);
+ nandc_write(nandc, NAND_DEV_CMD_VLD, NAND_DEV_CMD_VLD_VAL);
/* enable ADM DMA */
nandc_write(nandc, NAND_FLASH_CHIP_SELECT, DM_EN);
/* save the original values of these registers */
nandc->cmd1 = nandc_read(nandc, NAND_DEV_CMD1);
- nandc->vld = nandc_read(nandc, NAND_DEV_CMD_VLD);
+ nandc->vld = NAND_DEV_CMD_VLD_VAL;
return 0;
}
--
2.14.2