From: Viswas G <Viswas.G@microsemi.com>
Date: Wed, 18 Oct 2017 11:39:09 +0530
Subject: scsi: pm80xx: Different SAS addresses for phys.
Patch-mainline: v4.15-rc1
Git-commit: 6c85e4bcfd7c07ca20c0d8ad1bdde652ef99131f
References: FATE#322890, bsc#1049518

Different SAS addresses are assigned for each set of phys.

Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/pm8001/pm8001_init.c |   13 +++++++++----
 drivers/scsi/pm8001/pm80xx_hwi.c  |    3 +--
 2 files changed, 10 insertions(+), 6 deletions(-)

--- a/drivers/scsi/pm8001/pm8001_init.c
+++ b/drivers/scsi/pm8001/pm8001_init.c
@@ -132,7 +132,7 @@ static void pm8001_phy_init(struct pm800
 	sas_phy->oob_mode = OOB_NOT_CONNECTED;
 	sas_phy->linkrate = SAS_LINK_RATE_UNKNOWN;
 	sas_phy->id = phy_id;
-	sas_phy->sas_addr = &pm8001_ha->sas_addr[0];
+	sas_phy->sas_addr = (u8 *)&phy->dev_sas_addr;
 	sas_phy->frame_rcvd = &phy->frame_rcvd[0];
 	sas_phy->ha = (struct sas_ha_struct *)pm8001_ha->shost->hostdata;
 	sas_phy->lldd_phy = phy;
@@ -591,10 +591,12 @@ static void  pm8001_post_sas_ha_init(str
 	for (i = 0; i < chip_info->n_phy; i++) {
 		sha->sas_phy[i] = &pm8001_ha->phy[i].sas_phy;
 		sha->sas_port[i] = &pm8001_ha->port[i].sas_port;
+		sha->sas_phy[i]->sas_addr =
+			(u8 *)&pm8001_ha->phy[i].dev_sas_addr;
 	}
 	sha->sas_ha_name = DRV_NAME;
 	sha->dev = pm8001_ha->dev;
-
+	sha->strict_wide_ports = 1;
 	sha->lldd_module = THIS_MODULE;
 	sha->sas_addr = &pm8001_ha->sas_addr[0];
 	sha->num_phys = chip_info->n_phy;
@@ -611,6 +613,7 @@ static void  pm8001_post_sas_ha_init(str
 static void pm8001_init_sas_add(struct pm8001_hba_info *pm8001_ha)
 {
 	u8 i, j;
+	u8 sas_add[8];
 #ifdef PM8001_READ_VPD
 	/* For new SPC controllers WWN is stored in flash vpd
 	*  For SPC/SPCve controllers WWN is stored in EEPROM
@@ -672,10 +675,12 @@ static void pm8001_init_sas_add(struct p
 			pm8001_ha->sas_addr[j] =
 					payload.func_specific[0x804 + i];
 	}
-
+	memcpy(sas_add, pm8001_ha->sas_addr, SAS_ADDR_SIZE);
 	for (i = 0; i < pm8001_ha->chip->n_phy; i++) {
+		if (i && ((i % 4) == 0))
+			sas_add[7] = sas_add[7] + 4;
 		memcpy(&pm8001_ha->phy[i].dev_sas_addr,
-			pm8001_ha->sas_addr, SAS_ADDR_SIZE);
+			sas_add, SAS_ADDR_SIZE);
 		PM8001_INIT_DBG(pm8001_ha,
 			pm8001_printk("phy %d sas_addr = %016llx\n", i,
 			pm8001_ha->phy[i].dev_sas_addr));
--- a/drivers/scsi/pm8001/pm80xx_hwi.c
+++ b/drivers/scsi/pm8001/pm80xx_hwi.c
@@ -3041,7 +3041,6 @@ hw_event_phy_down(struct pm8001_hba_info
 	port->port_state = portstate;
 	phy->identify.device_type = 0;
 	phy->phy_attached = 0;
-	memset(&phy->dev_sas_addr, 0, SAS_ADDR_SIZE);
 	switch (portstate) {
 	case PORT_VALID:
 		break;
@@ -4394,7 +4393,7 @@ pm80xx_chip_phy_start_req(struct pm8001_
 	payload.sas_identify.dev_type = SAS_END_DEVICE;
 	payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL;
 	memcpy(payload.sas_identify.sas_addr,
-		pm8001_ha->sas_addr, SAS_ADDR_SIZE);
+	  &pm8001_ha->phy[phy_id].dev_sas_addr, SAS_ADDR_SIZE);
 	payload.sas_identify.phy_id = phy_id;
 	ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload, 0);
 	return ret;