From: Antoine Tenart <antoine.tenart@free-electrons.com>
Date: Wed, 30 Aug 2017 10:29:18 +0200
Subject: net: mvpp2: do not set GMAC autoneg when using XLG MAC
Patch-mainline: v4.14-rc1
Git-commit: 65a2c09aea8b9b620bbb3e59f68090a2b7151865
References: bsc#1098633

When using the XLG MAC, it does not make sense to force the GMAC autoneg
parameters. This patch adds checks to only set the GMAC autoneg
parameters when needed (i.e. when not using the XLG MAC).

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
---
 drivers/net/ethernet/marvell/mvpp2.c |   64 ++++++++++++++++++++++-------------
 1 file changed, 42 insertions(+), 22 deletions(-)

--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -5735,6 +5735,37 @@ static irqreturn_t mvpp2_isr(int irq, vo
 	return IRQ_HANDLED;
 }
 
+static void mvpp2_gmac_set_autoneg(struct mvpp2_port *port,
+				   struct phy_device *phydev)
+{
+	u32 val;
+
+	if (port->phy_interface != PHY_INTERFACE_MODE_RGMII &&
+	    port->phy_interface != PHY_INTERFACE_MODE_RGMII_ID &&
+	    port->phy_interface != PHY_INTERFACE_MODE_RGMII_RXID &&
+	    port->phy_interface != PHY_INTERFACE_MODE_RGMII_TXID &&
+	    port->phy_interface != PHY_INTERFACE_MODE_SGMII)
+		return;
+
+	val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+	val &= ~(MVPP2_GMAC_CONFIG_MII_SPEED |
+		 MVPP2_GMAC_CONFIG_GMII_SPEED |
+		 MVPP2_GMAC_CONFIG_FULL_DUPLEX |
+		 MVPP2_GMAC_AN_SPEED_EN |
+		 MVPP2_GMAC_AN_DUPLEX_EN);
+
+	if (phydev->duplex)
+		val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+
+	if (phydev->speed == SPEED_1000)
+		val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
+	else if (phydev->speed == SPEED_100)
+		val |= MVPP2_GMAC_CONFIG_MII_SPEED;
+
+	writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+
+}
+
 /* Adjust link */
 static void mvpp2_link_event(struct net_device *dev)
 {
@@ -5745,24 +5776,7 @@ static void mvpp2_link_event(struct net_
 	if (phydev->link) {
 		if ((port->speed != phydev->speed) ||
 		    (port->duplex != phydev->duplex)) {
-			u32 val;
-
-			val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
-			val &= ~(MVPP2_GMAC_CONFIG_MII_SPEED |
-				 MVPP2_GMAC_CONFIG_GMII_SPEED |
-				 MVPP2_GMAC_CONFIG_FULL_DUPLEX |
-				 MVPP2_GMAC_AN_SPEED_EN |
-				 MVPP2_GMAC_AN_DUPLEX_EN);
-
-			if (phydev->duplex)
-				val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
-
-			if (phydev->speed == SPEED_1000)
-				val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
-			else if (phydev->speed == SPEED_100)
-				val |= MVPP2_GMAC_CONFIG_MII_SPEED;
-
-			writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+			mvpp2_gmac_set_autoneg(port, phydev);
 
 			port->duplex = phydev->duplex;
 			port->speed  = phydev->speed;
@@ -5773,10 +5787,16 @@ static void mvpp2_link_event(struct net_
 		port->link = phydev->link;
 
 		if (phydev->link) {
-			val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
-			val |= (MVPP2_GMAC_FORCE_LINK_PASS |
-				MVPP2_GMAC_FORCE_LINK_DOWN);
-			writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+			if (port->phy_interface == PHY_INTERFACE_MODE_RGMII ||
+			    port->phy_interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			    port->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID ||
+			    port->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID ||
+			    port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+				val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+				val |= (MVPP2_GMAC_FORCE_LINK_PASS |
+					MVPP2_GMAC_FORCE_LINK_DOWN);
+				writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+			}
 
 			mvpp2_interrupts_enable(port);
 			mvpp2_port_enable(port);