From: Eric Yang <Eric.Yang2@amd.com>
Date: Wed, 21 Feb 2018 16:37:16 -0500
Subject: drm/amd/display: update infoframe after dig fe is turned on
Git-commit: db941f2412882b05b8bcdc26c75860dfa0e08d2e
Patch-mainline: v4.16-rc5
References: FATE#326289 FATE#326079 FATE#326049 FATE#322398 FATE#326166

Before dig fe is enabled, infoframe can't be programmed. So in
suspend resume case our infoframe programmming was not going through.

This change changes the sequence so that infoframe is programmed
after.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Petr Tesarik <ptesarik@suse.com>
---
 drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c |   23 ++++++------
 1 file changed, 13 insertions(+), 10 deletions(-)

--- a/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c
+++ b/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c
@@ -688,15 +688,22 @@ void dce110_enable_stream(struct pipe_ct
 	struct dc_crtc_timing *timing = &pipe_ctx->stream->timing;
 	struct dc_link *link = pipe_ctx->stream->sink->link;
 
-	/* 1. update AVI info frame (HDMI, DP)
-	 * we always need to update info frame
-	*/
+
 	uint32_t active_total_with_borders;
 	uint32_t early_control = 0;
 	struct timing_generator *tg = pipe_ctx->stream_res.tg;
 
-	/* TODOFPGA may change to hwss.update_info_frame */
+	/* For MST, there are multiply stream go to only one link.
+	 * connect DIG back_end to front_end while enable_stream and
+	 * disconnect them during disable_stream
+	 * BY this, it is logic clean to separate stream and link */
+	link->link_enc->funcs->connect_dig_be_to_fe(link->link_enc,
+						    pipe_ctx->stream_res.stream_enc->id, true);
+
+	/* update AVI info frame (HDMI, DP)*/
+	/* TODO: FPGA may change to hwss.update_info_frame */
 	dce110_update_info_frame(pipe_ctx);
+
 	/* enable early control to avoid corruption on DP monitor*/
 	active_total_with_borders =
 			timing->h_addressable
@@ -717,12 +724,8 @@ void dce110_enable_stream(struct pipe_ct
 			pipe_ctx->stream_res.stream_enc->funcs->dp_audio_enable(pipe_ctx->stream_res.stream_enc);
 	}
 
-	/* For MST, there are multiply stream go to only one link.
-	 * connect DIG back_end to front_end while enable_stream and
-	 * disconnect them during disable_stream
-	 * BY this, it is logic clean to separate stream and link */
-	link->link_enc->funcs->connect_dig_be_to_fe(link->link_enc,
-						    pipe_ctx->stream_res.stream_enc->id, true);
+
+
 
 }