From: Benedikt Spranger <b.spranger@linutronix.de>
Date: Mon, 8 Mar 2010 18:57:04 +0100
Subject: clocksource: TCLIB: Allow higher clock rates for clock events
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git
Git-commit: 0e65abeac3da31012c04423c779e6fb9754383bc
Patch-mainline: Queued in subsystem maintainer repository
References: SLE Realtime Extension
As default the TCLIB uses the 32KiHz base clock rate for clock events.
Add a compile time selection to allow higher clock resulution.
(fixed up by Sami Pietikäinen <Sami.Pietikainen@wapice.com>)
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Mike Galbraith <mgalbraith@suse.de>
---
drivers/clocksource/tcb_clksrc.c | 36 +++++++++++++++++++++---------------
drivers/misc/Kconfig | 12 ++++++++++--
2 files changed, 31 insertions(+), 17 deletions(-)
--- a/drivers/clocksource/tcb_clksrc.c
+++ b/drivers/clocksource/tcb_clksrc.c
@@ -23,8 +23,7 @@
* this 32 bit free-running counter. the second channel is not used.
*
* - The third channel may be used to provide a 16-bit clockevent
- * source, used in either periodic or oneshot mode. This runs
- * at 32 KiHZ, and can handle delays of up to two seconds.
+ * source, used in either periodic or oneshot mode.
*
* A boot clocksource and clockevent source are also currently needed,
* unless the relevant platforms (ARM/AT91, AVR32/AT32) are changed so
@@ -75,6 +74,7 @@ struct tc_clkevt_device {
struct clock_event_device clkevt;
struct clk *clk;
bool clk_enabled;
+ u32 freq;
void __iomem *regs;
};
@@ -83,13 +83,6 @@ static struct tc_clkevt_device *to_tc_cl
return container_of(clkevt, struct tc_clkevt_device, clkevt);
}
-/* For now, we always use the 32K clock ... this optimizes for NO_HZ,
- * because using one of the divided clocks would usually mean the
- * tick rate can never be less than several dozen Hz (vs 0.5 Hz).
- *
- * A divided clock could be good for high resolution timers, since
- * 30.5 usec resolution can seem "low".
- */
static u32 timer_clock;
static void tc_clk_disable(struct clock_event_device *d)
@@ -139,7 +132,7 @@ static int tc_set_oneshot(struct clock_e
tc_clk_enable(d);
- /* slow clock, count up to RC, then irq and stop */
+ /* count up to RC, then irq and stop */
__raw_writel(timer_clock | ATMEL_TC_CPCSTOP | ATMEL_TC_WAVE |
ATMEL_TC_WAVESEL_UP_AUTO, regs + ATMEL_TC_REG(2, CMR));
__raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
@@ -161,10 +154,10 @@ static int tc_set_periodic(struct clock_
*/
tc_clk_enable(d);
- /* slow clock, count up to RC, then irq and restart */
+ /* count up to RC, then irq and restart */
__raw_writel(timer_clock | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
regs + ATMEL_TC_REG(2, CMR));
- __raw_writel((32768 + HZ / 2) / HZ, tcaddr + ATMEL_TC_REG(2, RC));
+ __raw_writel((tcd->freq + HZ / 2) / HZ, tcaddr + ATMEL_TC_REG(2, RC));
/* Enable clock and interrupts on RC compare */
__raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
@@ -191,7 +184,11 @@ static struct tc_clkevt_device clkevt =
.features = CLOCK_EVT_FEAT_PERIODIC |
CLOCK_EVT_FEAT_ONESHOT,
/* Should be lower than at91rm9200's system timer */
+#ifdef CONFIG_ATMEL_TCB_CLKSRC_USE_SLOW_CLOCK
.rating = 125,
+#else
+ .rating = 200,
+#endif
.set_next_event = tc_next_event,
.set_state_shutdown = tc_shutdown_clk_off,
.set_state_periodic = tc_set_periodic,
@@ -213,8 +210,9 @@ static irqreturn_t ch2_irq(int irq, void
return IRQ_NONE;
}
-static int __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
+static int __init setup_clkevents(struct atmel_tc *tc, int divisor_idx)
{
+ unsigned divisor = atmel_tc_divisors[divisor_idx];
int ret;
struct clk *t2_clk = tc->clk[2];
int irq = tc->irq[2];
@@ -235,7 +233,11 @@ static int __init setup_clkevents(struct
clkevt.regs = tc->regs;
clkevt.clk = t2_clk;
- timer_clock = clk32k_divisor_idx;
+ timer_clock = divisor_idx;
+ if (!divisor)
+ clkevt.freq = 32768;
+ else
+ clkevt.freq = clk_get_rate(t2_clk) / divisor;
clkevt.clkevt.cpumask = cpumask_of(0);
@@ -246,7 +248,7 @@ static int __init setup_clkevents(struct
return ret;
}
- clockevents_config_and_register(&clkevt.clkevt, 32768, 1, 0xffff);
+ clockevents_config_and_register(&clkevt.clkevt, clkevt.freq, 1, 0xffff);
return ret;
}
@@ -383,7 +385,11 @@ static int __init tcb_clksrc_init(void)
goto err_disable_t1;
/* channel 2: periodic and oneshot timer support */
+#ifdef CONFIG_ATMEL_TCB_CLKSRC_USE_SLOW_CLOCK
ret = setup_clkevents(tc, clk32k_divisor_idx);
+#else
+ ret = setup_clkevents(tc, best_divisor_idx);
+#endif
if (ret)
goto err_unregister_clksrc;
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -69,8 +69,7 @@ config ATMEL_TCB_CLKSRC
are combined to make a single 32-bit timer.
When GENERIC_CLOCKEVENTS is defined, the third timer channel
- may be used as a clock event device supporting oneshot mode
- (delays of up to two seconds) based on the 32 KiHz clock.
+ may be used as a clock event device supporting oneshot mode.
config ATMEL_TCB_CLKSRC_BLOCK
int
@@ -84,6 +83,15 @@ config ATMEL_TCB_CLKSRC_BLOCK
TC can be used for other purposes, such as PWM generation and
interval timing.
+config ATMEL_TCB_CLKSRC_USE_SLOW_CLOCK
+ bool "TC Block use 32 KiHz clock"
+ depends on ATMEL_TCB_CLKSRC
+ default y
+ help
+ Select this to use 32 KiHz base clock rate as TC block clock
+ source for clock events.
+
+
config DUMMY_IRQ
tristate "Dummy IRQ handler"
default n